what turbo setup for carbed windsor?? - Ford Mustang Forums : Corral.net Mustang Forum
 
LinkBack Thread Tools Display Modes
post #1 of 7 Old 07-23-2016, 10:37 PM Thread Starter
Registered User
 
richstang75's Avatar
 
Trader Feedback: (5)
Join Date: Feb 2009
Location: Paulding, Ohio
Posts: 437
Garage
Arrow what turbo setup for carbed windsor??

I'm thinking of running a Turbo on my 357w. I'm just wanting to go with 8-10 psi maybe a single 70mm with blow thru setup and carb hat. What would be best way to go since most kits are efi? Thanks in advance. -Rich

richstang75 is offline  
Sponsored Links
Advertisement
 
post #2 of 7 Old 07-25-2016, 10:29 AM
Registered User
 
Dustang83's Avatar
 
Trader Feedback: (9)
Join Date: Aug 2004
Location: Wakeman, OH
Posts: 858
Garage
I just used an on3 EFI kit and was able to reuse a lot of the 3" stainless cold side piping. I also picked up a universal 3" aluminum cold side piping kit which matched the stainless pretty closely.

Universal DIY 8PC 3" Intercooler Aluminum Racing Turbo Intercooler Fmic Piping | eBay


'93 LX Hatch - 331
'79 Fairmont Futura Sport Coupe - Novi 1k
'67 Comet Caliente Hardtop - 76mm on3 302
Dustang83 is offline  
post #3 of 7 Old 07-25-2016, 01:10 PM Thread Starter
Registered User
 
richstang75's Avatar
 
Trader Feedback: (5)
Join Date: Feb 2009
Location: Paulding, Ohio
Posts: 437
Garage
Sounds good. I wasn't sure if there was much extra I'd need. The on 3 kit it the one I was looking at. Is yours working good?
richstang75 is offline  
Sponsored Links
Advertisement
 
post #4 of 7 Old 07-25-2016, 02:45 PM
Registered User
 
Dustang83's Avatar
 
Trader Feedback: (9)
Join Date: Aug 2004
Location: Wakeman, OH
Posts: 858
Garage
Haven't been able to put enough street time on it yet to judge much. I did have to open up the bolt holes on the manifolds quite a bit, but a few minutes with the grinder took care of it. Other than that I don't have any complaints.

'93 LX Hatch - 331
'79 Fairmont Futura Sport Coupe - Novi 1k
'67 Comet Caliente Hardtop - 76mm on3 302
Dustang83 is offline  
post #5 of 7 Old 08-10-2016, 11:41 PM
Registered User
 
boosted85coupe's Avatar
 
Trader Feedback: (1)
Join Date: Apr 2013
Location: Hawaii
Posts: 110
I've done the 357w with on3 also... With a 1.69glide.. Runs good... (Good enuff it blew up my built C4 and that's why I went Glide)...

Decided to change cars also after tranny bit it... Lol

Building 98 now with cage, just about a back half car with stock suspension points still for classes... If u wana know anything just lmk...
boosted85coupe is offline  
post #6 of 7 Old 08-11-2016, 01:23 AM
Registered User
 
boosted85coupe's Avatar
 
Trader Feedback: (1)
Join Date: Apr 2013
Location: Hawaii
Posts: 110
As it sits now...



Not done yet but she's in the shop getting tub'ed, caged and "ready"... Needs wiring, fuel and final time with new set-up but I'll knock that out once it drops below 200* every day outside!!! Haha

Here are a few more pics of the build/swap
boosted85coupe is offline  
post #7 of 7 Old 08-11-2016, 07:47 AM Thread Starter
Registered User
 
richstang75's Avatar
 
Trader Feedback: (5)
Join Date: Feb 2009
Location: Paulding, Ohio
Posts: 437
Garage
Here's mine as of now. I have a lot of room in engine bay. Gotta move alternator to drivers side. I don't have a heated garage to wrench in the winter so probably won't finish Turbo til spring. I'll post pics then.
[IMG][/IMG]
richstang75 is offline  
Sponsored Links
Advertisement
 
Reply

Bookmarks

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the Ford Mustang Forums : Corral.net Mustang Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in










Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes
Linear Mode Linear Mode



Similar Threads
Thread Thread Starter Forum Replies Last Post
For Sale DSS Pro Bullet/TFS Street Heat Top end, B&G turbo setup jethot coated, Mega squirt 8urvette1 Windsor Engine Parts 2 01-23-2013 11:33 PM
Want To Buy 302/351 Turbo Motor Setup 1990LX Windsor Engine Parts 1 12-11-2012 07:22 PM
Crane 2031 cam a good choice for my GT40 W/ turbo setup? stangbanger88 Turbochargers 0 02-11-2011 06:51 AM

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome