Welding MAF on3 perf. kit - Ford Mustang Forums : Corral.net Mustang Forum
 
LinkBack Thread Tools Display Modes
post #1 of 8 Old 11-27-2012, 11:12 PM Thread Starter
Registered User
 
Trader Feedback: (0)
Join Date: Mar 2012
Location: Northfield, MN
Posts: 6
Welding MAF on3 perf. kit

hey guys almost finished up building the motor for the on3 kit. I see on3's website says theyll weld the bracket on for the MAF for $25. has anyone done this? Does anyone know if i can send the pipe in to get welded even though i already have the kit?
thanks, nate

nhildahl is offline  
Sponsored Links
Advertisement
 
post #2 of 8 Old 11-28-2012, 01:13 PM
Registered User
 
Trader Feedback: (14)
Join Date: Jun 2005
Location: Woodland, CA....Nor Cal
Posts: 2,530
it's just a little square block that any muffler shop can weld on....


'18 Charger Hellcat
95 Cobra - Comp Billet PT8047 DIY Turbo and 340CI A4 Car
Palm Beach Dyno tuned - juuuuuuuust a little over 385RWHP....
RIP - Jerry"BabyLove" Glover ....1952 to 2012...
chinopsu is offline  
post #3 of 8 Old 11-28-2012, 01:42 PM
Registered User
 
Trader Feedback: (3)
Join Date: Jan 2012
Location: New Lexington
Posts: 53
DO Yourself a favor if you haven't already bought the meter and install an Abaco 85mm inline instead!
tthomp is offline  
Sponsored Links
Advertisement
 
post #4 of 8 Old 11-28-2012, 10:17 PM Thread Starter
Registered User
 
Trader Feedback: (0)
Join Date: Mar 2012
Location: Northfield, MN
Posts: 6
I figured that would require a tig welder to do? correct me if im wrong. and i already purchased a maf through on3
nhildahl is offline  
post #5 of 8 Old 11-29-2012, 08:39 AM
Registered User
 
JKolbfleisch's Avatar
 
Trader Feedback: (4)
Join Date: Jun 2011
Location: Fort Lee, VA
Posts: 223
It will cost you more in shipping than it would cost to have a local welder do it. Any decent welder with a TIG can do it.

1965 AC Cobra 427SC Replica [Carb Edelbrock 306ci SBF, 1980lbs]
2001 Mustang GT - [645WHP, 652TQ][MMR900 + Trick Flow Heads + Intake][ON3 Turbo @ 14psi]
2007 Jeep Grand Cherokee HEMI, 2006 Infiniti G35, 2012 Honda CRV EXL [The Daily Drivers!]
JKolbfleisch is offline  
post #6 of 8 Old 11-29-2012, 10:04 AM
Registered User
 
Trader Feedback: (33)
Join Date: Jun 2002
Location: Meridian, Mississippi
Posts: 3,095
Actually, if it's stainless, you can mig it too if you have the right tire in your machine. That's what I did to mine.

1987 Saleen clone: 358cid, FoxLake Vic Jr's, Victor 5.0, YSi, etc, etc, etc
809rwhp on pump gas + meth injection
"Just turn the boost up.....it's only air."
tireburner163 is offline  
post #7 of 8 Old 11-29-2012, 06:49 PM
Registered User
 
Trader Feedback: (1)
Join Date: Dec 2008
Location: windsor ont
Posts: 206
You can mig stainless you just have to paint the welds or they rust! I did mine with a mig with no problem!
rjm177 is offline  
post #8 of 8 Old 11-30-2012, 01:42 AM
Registered User
 
Trader Feedback: (1)
Join Date: Apr 2005
Location: IL
Posts: 226
My MAF pipe was too short, which requires me to buy the VMP HPX MAF and housing, I'll use couples to connect it to the two pipes in fender
bionic_chronik is offline  
Sponsored Links
Advertisement
 
Reply

Bookmarks

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the Ford Mustang Forums : Corral.net Mustang Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in










Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes
Linear Mode Linear Mode



Similar Threads
Thread Thread Starter Forum Replies Last Post
Please help no one else can g3mustang General Mustang Tech 155 06-13-2012 09:11 PM
For Sale On3 performance turbo kit, wideband, sct, etc 100% complete turbo kit all mostly bnib n/a3valve S197 and Coyote Parts 2 06-02-2012 09:19 PM
on3 turbo company...(horrible problems with kit) 99oRallyClipse Turbochargers 83 10-01-2011 11:57 AM
MAC cold air kit vs. C&L 80mm MAF KIT Gtstang00 GT & SOHC 0 12-26-2001 08:57 PM

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome