For Sale 86 Mustang GT, TKO500, AEM (no engine) - Ford Mustang Forums : Mustang Forum
LinkBack Thread Tools Display Modes
post #1 of 2 Old 11-29-2012, 09:01 PM Thread Starter
Registered User
Trader Feedback: (9)
Join Date: Nov 2001
Location: Uniontown, PA USA
Posts: 294
86 Mustang GT, TKO500, AEM (no engine)-sold

1986 Ford Mustang GT - Drag setup but still street legal and driven
Ran 10.3 @ 139 (with 408 engine and vortech supercharger)

No Engine (sold engine and supercharger 3 years ago)

Clear title (owned car since 98')

Car featured in Modified Mustangs Magazine.

All items below professionally installed and taken care of.

Selling due to changing priorities and lack of funds, I canít see storing the car in my garage if I will not be able to put a new engine in it in the near future.

Custom checkered Blue and pearl paint job

TKO 500 transmission - 26 spline input (purchased new, and has very low miles)
bellhousing setup for 351W
RAM HD Powergrip clutch
351 pressure plate (SFI approved)
351 Damper (SFI approved)
Aluminum driveshaft (mated output shaft for TKO 500)
Aluminum clutch quadrant - fast release
Steeda Adjustable clutch cable
AEM standalone computer for Mustang - fully programmed and setup for Speed Density w/GM MAP sensor (model 30-1400 EMS)
GM LQ9 wasted Spark ignition system (8 coil on plugs)
high volume intake pump(Walbro GSS340 HiPressure 255LPH Fuel Pump) , inline high volume pump, 1/2" braided fuel lines, 5/8 fuel rails, Areomotive FPR
solid motor mounts
polyurethane Transmission mount
polyurethane cross member mounts
polyurethane power steering mounts (offset)
ASP 7" Overdrive 8 rib one-piece crank pulley w/4" underdrive accessories and 3.33" SC pulley
Vortech high volume Aluminum Discharge Tube with Mondo bypass
K&N 9" Air Filter
Morpheus 4" Power Pipe
Trick Flow Tall Valve Covers
1.6 Stud Mount 7/16" Roller Rockers by Summit Racing (15 of them, one is broken)
75mm Throttle body and 75mm EGR plate
FMS Aluminum Driveshaft
FMS Mini-Starter (high torque)
UPR Smog Pump Eliminator Pulley
93 Cobra Overdrive WaterPump Pulley
ASP/FORD Underdrive power steering pump pulley
3G 130AMP alternator
AutoMeter 5" Monster Tach with shift light
Autometer 2 5/8 Water temp
Autometer 2 5/8 Oil Pressure
Autometer 2 5/8 Volt
Digital boost gage with memory
2 1/8 Fuel pressure gage
2 1/8 Vac/Boost
1 3/4" Full length 351W long tube headers with 3" ball and socket collectors
Custom 3" exhaust
3" 1 chamber Flowmaster mufflers with dumps
Wide Band O2 sensor - setup with AEM
5 bolt axles/drums
5 bolt 11" slotted rotors with green stuff pads
UPR chromoly K-member, A-arms, coilovers w/ 14"-130 springs
UPR bumpsteer kit
UPR chromoly solid upper and lower controls arms
UPR rear anti-rollbar
upper and lower battle boxes (welded)
Steeda full length sub-frame connectors (fully welded)
Weld draglite rims (front 15x6 - 225/50/15, rear 15x8 - 265/50/15 tires)
Mickey Thompson ET Street 26X11.5X15 Tires
Draglite 15X10 drag rims.
Strange 10 way adjustable shocks and struts
Global West Caster/Camber Plates
S&W 8 Point Roll Cage
RJS 5 Point Seat Belts (2)
Taylor Aluminum Battery Box mounted in the hatch Ė above RR tire (with battery)
Taylor 150AMP cutoff switch
Completely built 8.8 rear end
3.73 gears
Strange bullet end caps
aluminum diff cover
welded axle tubes
33 spline Moser axles
5/8 studs
9" bearings (welded on) [c clip eliminators]
lightweight spool
(rear built to handle over 800HP)
140 MPH speedometer
Autometer Electric Fuel Pressure Gauge
Autometer Boost Gauge
A-Pillar dual Gauge Pod
Harwood Pin-on 2.5" Cowl Induction Hood
Aluminum front and rear bumpers
Plastic headlights
SVO Leather Shift Knob
7 quart canfield oil pan w/supercharger drain port
Sony CDX-MP30 mp3 head unit
Sony Speakers 5 ľ Front, 6X9 Rear

Car passed tracked safety down to 10.00 second bracket.

I am selling all parts and items related to this hobby. I have many bins of related parts and previously removed, such as:
wiper motor, seat belts, springs, etc

Odometer reads around 130k, All modifications done in the last 30k

Car was parked 3 years ago after the 408 engine blew a piston. I then sold the engine and supercharger with plans on a bigger engine and blower. Car has been stored since.
Body is in fair shape. No dents, but several cracks, chips and scratches from years of burnouts and trailering.

Package deal for all
$6000 OBO

The only items I am willing to separate:
AEM 14-1300 Standalone Engine Management computer $1000
TKO 500 Transmission and shifter $2000
2 rear Weld Drag Lite 15X10 rims and MT ET Street 26 X 11.5 X 15 Tires $600

Also have a 15í open deck Econo trailer. Purchased new in 2006. Used very little to tow this car. Tires are perfect, always covered. LED lights, brakes work perfect.
Home (model ET154B-102)
Will sell trailer and car for $7500 (will help you load it).
Trailer alone for $2200

Cash or Paypal(I will pay Paypal fees)
Title transfer upon cash or validation of transaction
Location Uniontown PA 15401
Local sale only on all.

Attached Images
File Type: jpg mustangstationsquare.jpg (26.9 KB, 150 views)

Last edited by bellotti50; 12-27-2012 at 07:13 PM. Reason: Sold
bellotti50 is offline  
Sponsored Links
post #2 of 2 Old 12-03-2012, 10:33 PM Thread Starter
Registered User
Trader Feedback: (9)
Join Date: Nov 2001
Location: Uniontown, PA USA
Posts: 294

bellotti50 is offline  
Sponsored Links


Quick Reply

Register Now

In order to be able to post messages on the Ford Mustang Forums : Mustang Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:


Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes
Linear Mode Linear Mode

Similar Threads
Thread Thread Starter Forum Replies Last Post
2000 GT SOHC to DOHC swap... (Using a 1997 Mark VIII Engine ) An82Mustang SVT & DOHC 53 04-02-2016 09:24 PM
Want To Buy 07 or 08 automatic mustang gt engine harness asl9622 S197 and Coyote Parts 0 05-31-2012 05:33 PM
For Sale 1994 Mustang Gt, custom paint, fresh engine and tranny slowgtnky Mustangs For Sale/Wanted, 1994-1998 2 12-14-2010 05:51 PM
video - 2011 Ford Mustang GT 5.0L Engine on Dyno CorralTV Video 0 12-11-2010 08:00 PM
video - My 1967 Mustang GT with 393w idleing...engine bay. CorralTV Video 0 12-11-2010 08:00 PM

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

For the best viewing experience please update your browser to Google Chrome