For Sale 86' Notch W/ 87-93 Nose and Interior $4200 IN INDIANA - Ford Mustang Forums : Corral.net Mustang Forum
 
LinkBack Thread Tools Display Modes
post #1 of 1 Old 01-06-2012, 09:23 PM Thread Starter
Registered User
 
GMundertaker's Avatar
 
Trader Feedback: (72)
Join Date: Jun 2007
Location: Clinton Indiana
Posts: 1,199
86' Notch W/ 87-93 Nose and Interior $4200 IN INDIANA TKO trans built 8.8

Sold! Thanks Corral!!!












Ok All, here we go.

I have just acquired my old 86' coupe. It was a 4cyl back in the day. It has been converted to 5.0 The only thing left is the VIN. It has had body work done recently and has a fresh coat of Hot Rod black paint. In my opinion it is in nice shape. Some of the interior has been converted to 87-93 the console, dash, seats gauges etc.

The Bad: Needs a clutch if you are going to lean on it.
Missing the PS door panel
Heater controls have been removed, but could easily be hooked up
if you had some.
PS inner fenderwell is MIA
Antenna and wipers were removed
DS seat has the "gangsta lean"
All of these things could for the most part be irrelevant depending on what you are looking for.

The Good:

Car Has a Tremmec TKO 5 speed
Steeda shifter
Spec Stage 1 clutch, it is tucking out i'm afraid
Steeda firewall adjuster
Built 8.8 with 31 spline truck unit full of clutches
Moser 31 spline Axles with C-clip eliminators
3.73 FRPP gears
ARP wheel studs

Mac Upper and lower control arms?? Boxed, red..
Front 90/10s
Rear 3 way adjustable Comp Eng.
No sway bar
4 cyl front springs
V8 rear springs
Homemade frame ties
Driveshaft safety loop


302 that was rebuilt some years back
Forged pistons
Stock block
Stock rods
Has GT40P Heads
Hardened Pushrods
Crane springs locks and retainers
three angle valve job
ARP head bolts
Motorsports oil pump shaft
bore and stroke are stock crank is 10 over
2031 Cam
GT40 Intake
1.7 Crane roller rockers
19lb injectors
255lph intank pump
kirban adj regulator
65mm Throttle body
C&L 76mm mass air with K&N panel
Griffin aluminum radiator
Underdrive pulleys
Smog delete
3G Alternator upgrade
MSD coil
Car still has Power steering

Has 7 autometer gauges in it.

Has MAC full length headers with 2.5" offroad H
Flowmaster Polished tailpipes 2.5" with Dynomax ultra flo welded mufflers

I'm sure there are things I am forgetting but this is going to make someone a solid coupe. I only wish I had the room to keep it!

$4200.00

Matt

Any questions don't hesitate!

Had the Car on a chassis dyno with this combo some years back, and not too many miles ago.

it made 268 RWHP and 301 Peak TQ.

When I had a mostly highway 35 mile drive to work this car averaged just under 24mpg all the time!

And on the rare occasion it ran the 1/8th mile around 8 seconds flat I wanna say at 84mph. I'm sure it has a 7 in it with some diligence without further mods.



























03' Terminator Cobra Coupe #920 MG

Last edited by GMundertaker; 01-22-2012 at 06:01 PM. Reason: info
GMundertaker is offline  
Sponsored Links
Advertisement
 
Reply

Bookmarks

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the Ford Mustang Forums : Corral.net Mustang Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in










Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes
Linear Mode Linear Mode



Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome