For Sale 1986 Mustang GT, no engine, drag setup, selling hobby - Ford Mustang Forums : Corral.net Mustang Forum
 
LinkBack Thread Tools Display Modes
post #1 of 1 Old 10-08-2010, 02:24 PM Thread Starter
Registered User
 
Trader Feedback: (9)
Join Date: Nov 2001
Location: Uniontown, PA USA
Posts: 294
1986 Mustang GT, no engine, drag setup, selling hobby

1986 Ford Mustang GT - Drag setup but still street legal and driven
Ran 10.3 @ 139 (with 408 and vortech supercharger)
Have all documents, timeslips and most receipts

No Engine

Clear title (owned car since 98')

All items below professionally installed and taken care of.
Selling due to losing job and moving.


Custom checkered Blue and pearl paint job
fiberglass lift off hood

ASP 7" Overdrive 8 rib one-piece crank pulley w/4" underdrive accessories and 3.33" SC pulley
Vortech high volume Aluminum Discharge Tube with Mondo bypass
K&N 9" Air Filter
Morpheus 4" Power Pipe
TKO 500 transmission - 26 spline input
bellhousing setup for 351W
RAM HD Powergrip clutch
351 pressure plate (SFI approved)
351 Damper (SFI approved)
Aluminum driveshaft (mated output shaft for TKO 500)
Aluminum clutch quadrant - fast release
Steeda Adjustable clutch cable
AEM standalone computer for Mustang - fully programmed and setup for Speed Density w/GM MAP sensor
GM LQ9 wasted Spark ignition system (8 coil on plugs)
high volume intake pump(Walbro GSS340 HiPressure 255LPH Fuel Pump) , inline high volume pump, 1/2" braided fuel lines, 5/8 fuel rails, Areomotive FPR
Snow Performance Methanol injection system, boost controller, multiple jets
Compucar Dry Nitrous system, purge, Numerous jets
solid motor mounts
polyurethane Transmission mount
polyurethane cross member mounts
polyurethane power steering mounts (offset)



Trick Flow Tall Valve Covers

1.6 Stud Mount 7/16" Roller Rockers by Summit Racing (15 - one broken)

75mm Throttle body and 75mm EGR plate

FMS Aluminum Driveshaft

FMS Mini-Starter

UPR Smog Pump Eliminator Pulley

93 Cobra Overdrive WaterPump Pulley

ASP/FORD Underdrive power steering pump pulley

3G 130AMP alternator

AutoMeter 5" Monster Tach with shift light
Autometer 2 5/8 Water temp
Autometer 2 5/8 Oil Pressure
Autometer 2 5/8 Volt
Digital boost gage with memory
2 1/8 Fuel pressure gage
2 1/8 Vac/Boost
1 3/4" Full length 351W long tube headers with 3" ball and socket collectors
Custom 3" exhaust
3" 1 chamber Flowmaster mufflers with dumps
Wide Band O2 sensor - setup with AEM

5 bolt axles/drums

5 bolt 11" slotted rotors with green stuff pads
UPR chromoly K-member, A-arms, coilovers w/ 14"-130 springs
UPR bumpsteer kit
UPR chromoly solid upper and lower controls arms
UPR rear anti-rollbar
upper and lower battle boxes (welded)

Steeda full length sub-frame connectors

Weld draglite rims (front 15x6 - 225/50/15, rear 15x8 - 265/50/15 tires)

Mickey Thompson ET Street 26X11.5X15 Tires
Draglite 15X10
Strange 10 way adjustable shocks and struts

Global West Caster/Camber Plates

S&W 8 Point Roll Cage

RJS 5 Point Seat Belts (2)

Taylor Aluminum Battery Box mounted in the hatch – above RR tire

Taylor 150AMP cutoff switch
Completely built 8.8 rear end
3.73 gears
Stange bullet end caps
aluminum diff cover
welded axle tubes
33 spline Moser axles
5/8 studs
9" bearings (welded on) [c clip eliminators]
lightweight spool


140 MPH speedometer

Autometer Electric Fuel Pressure Gauge

Autometer Boost Gauge

A-Pillar dual Gauge Pod

Harwood Pin-on 2.5" Cowl Induction Hood

Aluminum front and rear bumpers

Plastic headlights

SVO Leather Shift Knob

7 quart canfield oil pan w/supercharger drain port

Sony CDX-MP30 mp3 head unit

Sony Speakers 5 ¼ Front, 6X9 Rear

Removed Rear Seat, Carpet Insulation, Front Sway Bar and sway bar mounts, Dogbone, Wipers, Washer tank, heater core, heater hoses


I am selling all parts and items related to this hobby. I have many bins of related parts and previously removed, such as:
wiper motor, seat belts, springs, etc

$7000
can take Visa/MC via Paypal.
Location Uniontown PA 15401

Attached Images
File Type: jpg mustangstationsquare.jpg (26.9 KB, 148 views)
bellotti50 is offline  
Sponsored Links
Advertisement
 
Reply

Bookmarks

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the Ford Mustang Forums : Corral.net Mustang Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in










Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes
Linear Mode Linear Mode



Similar Threads
Thread Thread Starter Forum Replies Last Post
F/S 1986 Mustang GT drag car/street car orangecapri Mustangs For Sale/Wanted, 1979-1986 1 08-21-2008 02:11 PM
selling turbo mustang w/drag radial kit tonyblack1994 Mustangs For Sale/Wanted, 1994-1998 2 08-12-2008 10:09 PM
thinking about selling my 331 engine setup BLOWN LX 90 Windsor Engine Parts 8 05-22-2007 05:56 PM
Selling the car :( **1986 Mustang 5.0 carb'd, auto** St. Louis TommysCarbd86 Mustangs For Sale/Wanted, 1979-1986 9 06-29-2005 09:28 AM
Selling my entire Mustang setup. Robert99v6 Power Adders 1 08-20-2004 08:26 AM

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome