For Sale 68 coupe Roller in NJ close to Philadelphia trades welcome - Ford Mustang Forums : Corral.net Mustang Forum
 
LinkBack Thread Tools Display Modes
post #1 of 4 Old 02-12-2013, 06:47 AM Thread Starter
Registered User
 
351clevormustang's Avatar
 
Trader Feedback: (9)
Join Date: Nov 2004
Location: NJ South 15 minutes from Philly
Posts: 972
68 coupe Roller in NJ close to Philadelphia trades welcome

1968 Roller Mustang Coupe for sale $3,000 or BO. Will Trade something equal in value, even bodywork on my fastback.

The coupe was once restored. Only one layer of paint is on the car Overall the body, frame, trunk are solid. The car needs paint. The interior is in fair condition. The car was running as of 2/12/2013, however, I am planning to swap motor, headers and a few other parts to go into my 68 fastback project.

Passenger floor board had water sitting and rusted I purposely dug out the hole to ensure the frame rail was in tact with no rust. I have brand new floor pans that come with the car. Also comes with the battery panel that should be replaced.

What will the car need to run again off the top of my head?
Motor and all accessories, headers, install new 2.5 exhaust that comes with the car, mufflers, new fuel lines, I would redo all brake lines and check the master cylinder that is on the car since I swapped the disk conversion to my fastback, battery and battery cable, rims and tires of your choice.

Please ask me questions! Please look at the car and determine what it will need. There are allot of pictures while it was running below. I will add another album that shows the car as it sits today.

Roller also comes with:
Rebuilt C-6 transmission with shift kit. Still mounted to car
Transmission Cross member and driveshaft.
8 inch rear
New Dual Exhaust (needs mufflers and brackets)
New Racing Shocks
Radiator

Additional Parts included not on the car... New Front springs, 2.5" Exhaust


See link to photo bucket for detailed pictures while it was running

68 Mustang Photos by nauglesh | Photobucket


Email me questions at [email protected]


Last edited by 351clevormustang; 02-12-2013 at 06:53 AM.
351clevormustang is offline  
Sponsored Links
Advertisement
 
post #2 of 4 Old 03-17-2013, 08:40 PM
Registered User
 
Streetracer09's Avatar
 
Trader Feedback: (3)
Join Date: May 2011
Location: Philly area
Posts: 464
Just curious, does this car have a Fuel injection harness? Also, do you have the '68 Coupe roller for sale on CL?

Streetracer09 is offline  
post #3 of 4 Old 04-03-2013, 10:19 AM
Corral Elite Member
 
toms5oh's Avatar
 
Trader Feedback: (1)
Join Date: Oct 2008
Location: nola
Posts: 272
Blog Entries: 1
Wish you were closer!

USS FIFE DD991
91 SSP FHP 349 5 speed 4:10 gears . 2011 grabber blue 3.7 with Roush exhaust, C&L intake 2013 gt 19 inch premium wheels.
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
toms5oh is offline  
Sponsored Links
Advertisement
 
post #4 of 4 Old 01-24-2014, 08:01 PM
Registered User
 
Trader Feedback: (15)
Join Date: Mar 2003
Location: Bath, PA
Posts: 233
68 coupe

Is this car still available?
Roger E. Kleiber is offline  
Sponsored Links
Advertisement
 
Closed Thread

Bookmarks

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the Ford Mustang Forums : Corral.net Mustang Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in










Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes
Linear Mode Linear Mode



Similar Threads
Thread Thread Starter Forum Replies Last Post
For Sale 92' trueblue coupe roller W/rebuildable shortblock $3500firm Truebluedevil02 Mustangs For Sale/Wanted, 1987-1993 14 12-05-2011 09:40 PM
For Sale 5.0/5spd swap with coupe roller DillRacing87gt Miscellaneous Mustang Parts 1 11-21-2011 04:02 PM
1969 Mustang Coupe Project kyb88 Classic Mustangs & Fords 0 09-03-2011 07:45 PM
Want To Trade 1987 coupe roller kninja Mustangs For Sale/Wanted, 1994-1998 1 04-21-2011 12:28 AM
Want To Trade 92 coupe, trade for sn95 roller or running. meangreencoupe Mustangs For Sale/Wanted, 1987-1993 7 11-21-2010 03:01 PM

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome