For Sale 1965 RESTO MOD FOR SALE - Ford Mustang Forums : Corral.net Mustang Forum
 
LinkBack Thread Tools Display Modes
post #1 of 6 Old 09-29-2012, 05:52 PM Thread Starter
Registered User
 
Trader Feedback: (18)
Join Date: Nov 2006
Location: FL
Posts: 157
1965 RESTO MOD FOR SALE

For Sale is a 1965 Ford Mustang Resto Mod.It stated out as a 64.5 spec-ed auto I6.The car is almost complete and only needs a few things to be finished all the costly and time consuming/hard work has been done.
[IMG][/IMG]
Motor;
The motor is a OEM Ford Remand.Long block 1983 5.0 H.O. 302 flat tappet with just under 3500 miles.It was originally purchased from and installed by Ford in 2002 into a 1983 gt by a good friend of mine before I purchased it in 08. After I purchased the motor It received a facelift and needed mods for the install into the 65.Motor is completely stock,valve train and bottom half have not been disassembled.It has..
[IMG][/IMG]

1)Stock.. Heads,cam ,push rods,rockers,tappets,pistons,connecting rods,crank,mains,etc.
2)New timing chain cover and new front chromed dip stick and tube.
3)New and Chromed 3g 94/95 style Alternator with chromed 95 Cobra Pulley
4)New melling oil pump,pickup,oil pump rod with clip and Chromed front sump oil pan with felpro permadry gasket and oem Ford oil pan bolts.
5)Eldelbrock Torker II 302 lower intake with new Eldelbrock Stainless 12 point lower intake bolts and Eldelbrock 650 carb.
6)New Trickflow tensioner relocater.
7)New Summit Racings Chromed Alternator Bracket.
8)New Summit Racings Chromed RR High flow water pump with chromed 93 Cobra water pump pulley.Water pump bolts are Stainless steel Arp.
9) The original oil dip stick hole on side of block has been freeze plugged.
10)180* stant thermo and Chromed thermo housing with threaded port for electric fan probe.ARP stainless hardware as well.
11)New 50 oz Ford Racing dampener with Stock chromed crank pulley and Oem ford hardware,also new felpro timing cover to crank gasket.
12)Fox bell style oil pressure sender.
13)New motor craft plugs,temp sender,and oil filter.
14)New belt.
15)88 Style chromed tensioner and New wazee pulley and high temp bearing.
I built this motor to be a Really nice looking and reliable first crank motor with a little go.. as horsepowers only in the 210-220 range.It has the room grow and would accept a nice blower for those looking to haul [email protected]@.
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]

Brakes; Specs as follows..FRONT and Fluid
1)New/Remand 94 Cobra booster
2)New 94 Cobra master
3)New SSBC adjustable prop. valve.
4)94 gutted prop valve with New Ford racing end plug
5)New brake light switch
6)New custom routed hardlines,fittings,and nuts.
7)New clutch/brake pedal assembly with new bushings and custom mounting plate for the large Cobra Booster.(the master clears the tower and tower supports.
8)New relocated pedal pin
9)New SSBC stainless steel hoses and banjo bolts with crush washers
10)New 01 Bullitt calipers,brackets,pads,pins,and c-clips
11)New Mustang Steve aluminum backing plates and grade 8 hardware.(mounted on remand 66 v8 spindles)
12)Custom V8 5- Lug front hubs with new races,bearings,and studs
13)13'' slotted rotors rotors are lug-centric to hubs
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]

REAR BRAKES AND REAR END
1)NEW 01 Bullitt rear calipers,brackets,pads
2)New slotted 11.65 rotors
3)94/95 rear hoses with custom mounting locations
4)New Mustang Steve backing plates with New axle bearingswith new grade 8 hardware
5)94/95 e-brake cables with following stock routing with cut fronts to tie in to the oem 65 cables
MOUNTED ON..
1)66 8" Rear 5-lug
2)Dis-assembled ,bead blasted and rebuilt third member and housing
3)Original 3.00 ring gear with open carrier
4)New bearings,seals,races,crush washer,etc..
5)New pinion seal and axle seals
6)Housing has mounting points for the 94/95 hoses to mount
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
SUSPENSION FRONT AND REAR
1)New KYB gas adjust shocks front and rear
2)New 1'' bbk lowering springs trimmed 1/2 a coil
3)New Front upper and lower a-arms,balljoints,spring perches and zerks,inner and outter tie rods,center link,Bushings,all greased with synthetic
4)Rebuilt steering gear
5)New steering gear grade 8 mounting hardware
6)New Eaton rear leaf springs with new shackles,bushings and grade 8 hardware.
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
WHEELS..
18X7.5 BBS RK ON ALL 4 CORNERS 42 OS
Excellent Shape,like new.
[IMG][/IMG]

[IMG][/IMG]

Body..The car has been sprayed BC/cc 67 Bullitt green with a matching green vinyl top.The front windshield has a new gasket.All the glass is original and in good shape.The hood,hindges and springs are new and work smooth and flawlessly.(hood is new and needs to be sprayed to match.The fenders,doors and trunk are all original.The door handles and mechs have been replaced with new.The Chrome window trim on the door and 1/4 window is original and has slight peppering.The bumpers,headlights,taillights,gas cap/cover are all new.The Body on this car is straight as an arrow..The previous owner had the floor pans replaced.The rocker panels are off as I was going to have them sprayed to match the BBS wheels.They are included just not on the car.

Interior. The carpet,headliner,and seat materials are newer.The interior is in really nice shape.Only thing needed inside is a dash pad.(removed for windshield replacement).


Transmission.The car is set up for 5 speed.
Comes with (not installed yet)
1)93 t-5 5speed
2)Brand new cross members and tranny mount.2 cross members 1 for t-5 with oem cables (Ron Morris)and 1 without oem brake cables NPD.
3)Oem ford flywheel 50 oz 3500 miles on it
4)Ford Racing clutch 3500 miles on it
5)Used bellhousing,motor plate,fork,and all hardware
6)New rear main and pilot bearing are already in motor.

What it needs..
Exhaust,83 distributor wires and coil,fuel pump,starter,Battery cables.2 main harnesses,clutch cable, and gas pedal(I have a 93 fox pedal that goes with it.)radiator hoses and radiator with electric fan.

Extras it comes with..
1)New Msd box
2)C6 driveshaft
3)Spare tire
4)New arm rest pads
5)used radiator
6)New hood positioning bolts and rubber.
7)New Global West weld-in subframe connectors.

Im selling this for way less than half of whats in to it.It will need to be picked up and paid for in cash,NO paypal.Title in hand.Needs to be trailered.Message me with any questions,cash offers,etc..Sorry no trades.

$9500.00

sleepn88 is offline  
Sponsored Links
Advertisement
 
post #2 of 6 Old 11-09-2012, 11:53 AM
Registered User
 
roberryhill's Avatar
 
Trader Feedback: (0)
Join Date: Jul 2011
Location: Oklahoma
Posts: 90
Where are you located at?

roberryhill is offline  
post #3 of 6 Old 01-03-2013, 05:56 PM
Registered User
 
93CobraPwr's Avatar
 
Trader Feedback: (0)
Join Date: Apr 2002
Location: Bloomington, Illinois
Posts: 657
I pulled the exif information from your Photo taken with an HTC Sensation and it appears you are near Fort Lauderdale, FL - can you confirm please?

----------
Completely out of the game.
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
93CobraPwr is offline  
Sponsored Links
Advertisement
 
post #4 of 6 Old 01-03-2013, 07:18 PM
Registered User
 
Trader Feedback: (0)
Join Date: Sep 2010
Location: Maryland
Posts: 9
In case anyone is wondering, this is a bargain. Good luck with the sale.

65 Hardtop, fuel injected 347, Comp XE282HR, AFR 185, Edelbrock RPM II, 70 MM TB, 30LB Injectors, Lightning MAF, T5, 9 inch 3.89, 4 wheel disc brakes, Borgeson PS Swap.
redcoupe347 is offline  
post #5 of 6 Old 01-03-2013, 08:26 PM
Registered User
 
NastyNotch306's Avatar
 
Trader Feedback: (8)
Join Date: Dec 2011
Location: Mass
Posts: 732
That is an awesome build, glws

"The world is a playground, you know that when your a kid, but somewhere along the way, everyone forget's it"
NastyNotch306 is offline  
post #6 of 6 Old 01-04-2013, 11:46 PM
Registered User
 
roberryhill's Avatar
 
Trader Feedback: (0)
Join Date: Jul 2011
Location: Oklahoma
Posts: 90
Does anyone ever get a response from this guy?


Sent from my iPhone using AutoGuide.com App
roberryhill is offline  
Sponsored Links
Advertisement
 
Reply

Bookmarks

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the Ford Mustang Forums : Corral.net Mustang Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in










Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes
Linear Mode Linear Mode



Similar Threads
Thread Thread Starter Forum Replies Last Post
For Sale Forged internals - mod max 17cc pistons, cobra crank, mod max h-beam rods hardhitter Modular Engine Parts 19 03-18-2014 02:35 PM
1968 punisher coupe efi resto mod svtmotorman The Body Shop 75 06-26-2012 05:10 PM
For Sale 5.0 resto mod set up dsfdlish Electronics and Entertainment 0 11-16-2011 05:12 PM
For Sale 10 second 66 resto mod! Show and track ready! n2omaverick Mustangs For Sale/Wanted 1978 and older 16 08-29-2011 01:19 PM

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome